I thought I would build a simple NOP tester thingy. I want to prove to myself that I don't have a faulty 65C02.

I decided to forget the LEDs and use my (not very good) 'scope
I expected a square wave on the address lines doubling in wavelength as I work up through the address lines A0-A15.
I further expected A0 to be twice the clock frequency.
I indeed got exactly that - that's good
-but-
Can anyone explain the glitches in voltage in the address lines that go in time with the clock? (Address lines are yellow, clock blue)
Also, why is there a double trace on the Low part of the address?

This is A0

and this is A1


Edit: I forgot to say, the whole idea of the NOP tester was to look for oddities with IRQs. You may remember from above that one of the things I seem to be encountering are spurious (and lots of) interrupts, even though IRQ pin is tied high. With the NOP tester I should get a nice sequence of binary count on the address pins, if this sequence suddenly goes out of sequence that tells me there are spurious interrupts happening. If it counts nice and sequentially then that proves there aren't interrupts happening. Further, the 6502 is out of my main circut, further removing uncertainties.

If an interrupt were taken, you'd see three consecutive writes - you should be able to see that clearly on the RnW line.

You have no bypass capacitors, by the look of it, so it's not surprising that each clock edge is causing a bounce seen on other signals.

Ahh, right. Thank you! Simple as that.
I'll look at the R/W line.

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

Yep. That was it. Bypass capacitors improved things a lot. Thanks for that. I just wondered what it was. I will know if I see it again!

Hi Adrian,

As I was researching my similar problem I came across this:

https://web.archive.org/web/20160410002234/http://www.sigcon.com/Pubs/edn/mutual_understanding.htm

You might find it helpful.

_________________
"The key is not to let the hardware sense any fear." - Radical Brad

Paganini. Thank you. Very much appreciated.

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

_________________
http://WilsonMinesCo.com/ lots of 6502 resources
The "second front page" is http://wilsonminesco.com/links.html .
What's an additional VIA among friends, anyhow?

It took ages but I rebuilt the SBC on new breadboard over the last couple of days.
Exactly the same result. A seeming lockup of interrrrrrrrrrrupts even with the IRQ and NMI pins tied high.

Today the new 65C02 arrived. Plugged it in and it worked immediately.
So, it indeed was faulty!

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

Mouser UK.

New one is from a good supplier on eBay. Mouser have a minimum order value that means if you buy something for £1, p&p is £29 (minimum orde value of £30).

_________________
http://WilsonMinesCo.com/ lots of 6502 resources
The "second front page" is http://wilsonminesco.com/links.html .
What's an additional VIA among friends, anyhow?

I am pretty sure the old one was a good one. It came from Mouser and I can't believe they would sell counterfeit anything. The markings are identical to the letter with the new one.

It did work - well, I never had it working well... probably my coding - but it did work. I suspect very much you are correct with the static theory.

Maybe you've already done this, but as a sanity check it's worth temporarily swapping the "bad" chip back in again. Of course the expectation is that the problem will reappear, but this isn't always the case. It's not uncommon for projects to fix themselves just as a result of the flexing and vibration associated with exchanging a chip or a PSU or whatever.

-- Jeff

_________________
In 1988 my 65C02 got six new registers and 44 new full-speed instructions!
https://laughtonelectronics.com/Arcana/ ... mmary.html