Page 1 of 1
AIM65 and the EPROM-burner described in INTERACTIVE07
Posted: Sun Jul 08, 2018 8:49 am
by oz6ym
I would like to make a EPROM-burner and found the diagram in INTERACTIVE07, but but..
The software for it is made in FORTH, and I do no FORTH, so I was thinking, if any one of you ever made this EPROM-burner, and have done the program for it?
If so, I will be very happy to receive a DUMP af this program, ready to burn into a EEPROM for my vingate AIM65 system.
In advance, Thanks for your help!
Vy 73 de OZ6YM, Palle
Re: AIM65 and the EPROM-burner described in INTERACTIVE07
Posted: Sun Jul 08, 2018 9:13 am
by GaBuZoMeu
Hi Palle,
could you either attach a link to the source you mentioned or the schematics?
Cheers,
Arne
Re: AIM65 and the EPROM-burner described in INTERACTIVE07
Posted: Sun Jul 08, 2018 2:02 pm
by BigEd
Re: AIM65 and the EPROM-burner described in INTERACTIVE07
Posted: Sun Jul 08, 2018 3:05 pm
by GaBuZoMeu
Thank you, BigEd!
Palle, I have built something very similar for my SYM. The biggest difference in the hardware is, I didn't use a relay. I first set up the select switch (2716 <=> 2732) then insert the EPROM, and then turn on the SYM. The programing voltage is applied "by hand". My program issues a message when it is required.
You may take a look a it, and then perhaps know what to do on your AIM.
Cheers,
Arne
EDIT(1): one file is slightly corrupted, don't know how to remove it
the upper one should be fine
EDIT(2): wrong one deleted
Re: AIM65 and the EPROM-burner described in INTERACTIVE07
Posted: Mon Jul 09, 2018 1:00 pm
by oz6ym
Hej Arne..
Thanks for the ASS-file.
Do you have any picture or diagram of your EPROM-programmer ?
Homepage maybee ??
de OZ6YM Palle
Re: AIM65 and the EPROM-burner described in INTERACTIVE07
Posted: Mon Jul 09, 2018 4:19 pm
by BillO
(1): one file is slightly corrupted, don't know how to remove it
the upper one should be fine
Edit your post, then scroll down to the section titled "Posted attachments". Find the unwanted attachment and click on "Delete file".
Re: AIM65 and the EPROM-burner described in INTERACTIVE07
Posted: Mon Jul 09, 2018 5:20 pm
by GaBuZoMeu
@BillO: THX
@Palle:
I attached a quickly redrawn schematic. I have no picture - I couldn't find that board, perhaps it's gone, dunno.
At the top of the ASM file there is a sort of schematic. If there are discrepancies between the new one and the one within the ASM file, trust the old one!
Cheers,
Arne
Re: AIM65 and the EPROM-burner described in INTERACTIVE07
Posted: Wed Jul 11, 2018 6:07 am
by oz6ym
Hello Arne!
Thank you very much for the drawing.
Here I can see that the difference to mine is quite small, only the relay change you do not have.
My final result can be seen here:
http://planker.dk/AIM65/eprom.htm
Thanks to you and BigEd for input.
de OZ6YM, Palle
Re: AIM65 and the EPROM-burner described in INTERACTIVE07
Posted: Wed Jul 11, 2018 6:46 am
by GaBuZoMeu
Hej Palle,
it is looking fine. And a fine picture to show how easy wire wrap goes
Just never forget: some 2532 (and a few 2716 as well) don't like 25V !!
Happy burning
Arne