Recently, I bought a 6502, and I want make a pc with it, but I think that mine is dead, so how can I test it, without another integrated or something too hard? Because I'm waiting for more stuff and in this moment, I just have the 6502, but I have too an Arduino and rpi3 and a lot of resistances and wires, and i don't know if I can use them

Hi, you could do a free run using a few resistor and led on a breadboard.
If you wire properly the different signals to VCC and GND, you just have to wire data bus so it always reads $EA(NOP).
If you have LEDs on the address bus, you should see it incrementing.
The only thing is you have to provide a clock signal, if it’s a recent 65c02, you can do it by hand with a button, but if it’s an older 6502 you’ll need to provide a real clock(can be a 555 timer).

From where did you purchase this 6502? Can you post a closeup photo of it so we can see the markings on it?

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

Welcome, sprx128! As noted above, if you search for "NOP test" or "NOP generator" you'll get the information you need. But we're always happy to help with further questions.

As BDD implies, any IC which isn't sold as new by a major distributor will carry some risk of not being exactly what it's sold as. It might be slightly different or totally different. These risks are, if you like, built in to the very low prices. We've had many previous discussions on this phenomenon, so it would be nice not to hash it all out again here. See for example
Bargain chips bought online - buyer beware!
and perhaps
65xx parts sources, genuine and fake

I think that my 6502 it's fake because the letters of the top were make with laser.

Sure

I don't have any problem with the clock I have a 555 and cd4017, but can you give me the esquematic?

Garth has spent considerable effort on his excellent primer pages, and I highly recommend them for beginners and experts alike.

Happy hacking!

_________________
Got a kilobyte lying fallow in your 65xx's memory map? Sprinkle some VTL02C on it and see how it grows on you!

Mike B. (about me) (learning how to github)

_________________
http://WilsonMinesCo.com/ lots of 6502 resources
The "second front page" is http://wilsonminesco.com/links.html .
What's an additional VIA among friends, anyhow?

Just to note: just because a chip is relabelled doesn't mean it isn't something like what the label says. The resellers are doing whatever they feel helps them in the marketplace.

As far as I understand the anecdotal evidence, there's a fair chance that NMOS and CMOS 6502s will appear in each other's clothing. For some hobby purposes, it's not too important which one you have. For other purposes, it will matter.

Is there any info, printed or in the molding on the under side ?

If you can’t wait until Garth comes back you can have a look there : https://coronax.wordpress.com/2012/11/1 ... n-circles/
It helped me a lot when I started playing with 6502 a few years ago.

Production of NMOS 6502s ceased many years ago, before the widespread use of laser marking. Most likely, you have a fake, and it may not even be a microprocessor at all.

As for Ø2 clock generation, the 555 timer is not a good choice, as said by Garth. The rise and fall times are slow. You would be better served with a CMOS clock oscillator.

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

_________________
http://WilsonMinesCo.com/ lots of 6502 resources
The "second front page" is http://wilsonminesco.com/links.html .
What's an additional VIA among friends, anyhow?

Since you have an Arduino, it's worth keeping in mind that it can generate the clock too. There are advantages to this, for the initial "does it work at all?": you can connect address lines to its inputs, have it read them on each cycle, and print them in a nice readable format.