Increasingly, that's the case with me. If the backspaces and deletes counted as CPM I would be up around 400+.

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

Every base is base 10!

Must be because most of us have 10 fingers.

Actually, in data communications the 10 more often than not has to do with the long-standing TIA-232/TIA-422/TIA-485 data format of 8N1, eight data bits, no parity and one stop bit. Since there is always a start bit involved, 10 bits are transmitted per byte. So an interface running at 115,200 bits per second (bps) has a theoretical throughput of 11,520 bytes per second (BPS). Also, to be pedantic, baud is not bits per second. Baud refers to the signaling or "symbol" rate on the wire, not the bit rate. In the early days, the two were one and the same, but parted company following the development of the Bell 103/212A standard for modems.

BTW, most long-time assembly language programmers are not "rigidly accustomed" to working in base-10. Hexadecimal is the lingua franca of much assembly language.

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

I have caught myself out a couple of times, thinking that 80 is half of 100, which of course it is in hex, but not in decimal. So, as they say, you can get used to anything. (It's a bit like driving on the wrong side of the road, it's relatively easy, but there's a danger of demagnetising yourself and not being quite sure.)

Every time I have visited the UK I have faced death trying to drive.

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

I think traffic is a bit more lively on this side of the Atlantic - driving in Italy is my most extreme experience. But then, it's a relatively limited experience.

To get back to wifi modems - I've just posted the follow up to my radio broadcasting challenge:
viewtopic.php?f=1&t=4411

Anywhere I've been in Italy is pretty tame compared to larger cities here. But nothing here holds a candle to Shanghai.

BigEd, I think you misspelt licence.

Ed, you're not allowed to use american english! At least one american is offended...

_________________
6502 sources on GitHub: https://github.com/Klaus2m5

No offence here, just abject confusion!

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

Sorry about the spelling. Must have been feeling a bit off-color.

Oh! -- right: color / colour.

I had a feeling you were being humourous. Even so, it took me a moment...

_________________
In 1988 my 65C02 got six new registers and 44 new full-speed instructions!
https://laughtonelectronics.com/Arcana/ ... mmary.html

Except those who are working in negabinary (base -2). Hard to have a negative number of fingers, but it's a fun base to work with for basic math.


Which is somewhat affected by the bit-width of the computers that they use most often. 36-bit machines tend to be better suited to octal, for example.

And this leaves aside the heavily octal nature of 6502 opcodes. Yes, you have to bit-reverse them for it to really show up, but it's plainly obvious once you do. Or you could look at the SPC700 instruction set. I seem to recall that it is suspiciously similar to the 6502 ('c02?) in terms of semantics, but with the instruction bitfields shuffled around and the official mnemonics altered to disguise the fact.

This color/colour difference always reminds me of a "conflict" in the USA during the 19th century concerning the proper word to be used to refer to the location where one goes to meet a train. One group liked the word "station" and another liked "depot." The first group objected to the second group's preference, saying that "station" was proper English and "depot," being a French word (dépôt), was not, and how dare anyone inject those nasty French words into the king's English. There was a big writeup about it in the magazine Locomotive, in which the magazine's editor sided with the "station" group.

In exploring the etymology of "station," it turns out that it is derived from Anglo-French estation, which morphed into Middle English stacioun. The first known use of "station" as we now spell it was in the late 17th century and early in British railway history, train stations were called stations, not depots (my guess is some 19th century Britons also objected to French words).

So neither group would have been able to eliminate any French from the name of the place where you go to catch your morning train to get to work.

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

Which is why much of UNIX (and Linux) has historical ties to octal notation.

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!

I'm going off-topic again, but I think we have one or two radio enthusiasts on the thread: here's a Ladybird book from 1972, with a charming but serious and thorough explanation of "how to build a transistor radio" - for children, but not only for children.
Two online copies of the book, here and here.
Via this writeup on Hackaday: Books you should read: Making a transistor radio. From the comments, it seems quite a few people got started with this book.