6502.org Forum Projects Code Documents Tools Forum
It is currently Sun Nov 24, 2024 5:15 am

View unanswered posts | View active topics


Board index » 6502.org Users Forum » Hardware

All times are UTC




Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 
  Previous topic | Next topic 
Author Message
agsb
 Post subject: A new toy memory map
PostPosted: Wed Nov 20, 2024 8:30 pm 
Offline

Joined: Mon Jan 09, 2023 9:33 pm
Posts: 29
Hello,

I'm learning how to make a 65C02 SBC toy, and ask all about if those circuits are correct.

Any suggestions or corrections, are welcome.

Planning use,

1 x 1.8543 Mhz

1 x W65C02
2 x W65C22
1 x NM6551

2 x HM62256
1 x AT28C64

1 x 74HC10
1 x 74HC00
1 x 74HC138

Thanks all,

PS. I repost this at SBC topics


Attachments:
65C02.TOYC.png
65C02.TOYC.png [ 24.17 KiB | Viewed 41 times ]
65C02.TOY.png
65C02.TOY.png [ 147.38 KiB | Viewed 101 times ]


Last edited by agsb on Thu Nov 21, 2024 2:47 pm, edited 1 time in total.
Top
 Profile  
Reply with quote  
GARTHWILSON
 Post subject: Re: A new toy memory map
PostPosted: Wed Nov 20, 2024 9:37 pm 
Offline
User avatar

Joined: Fri Aug 30, 2002 1:09 am
Posts: 8546
Location: Southern California
agsb wrote:
PS. I repost this at SBC topics

Please don't, as it adds needless clutter to the forum.  I think everyone here already checks the entire forum regularly except perhaps the BASIC or Forth sections if they're not interested in those.  Also, when you have more development on the same project and topic, please keep it together, even if you think it's old.  A lot of people think they have to start a new thread about the same thing just because the one is old; but it's better to keep going on the original one, for these reasons:

  • to keep the related stuff together,
  • to avoid repeating information (particularly in the replies), and also
  • to avoid cluttering the forum with duplicate topics; and
  • if the same one is continued, those who have posted there get an email notification of replies (when notifications work).

Thanks.

Garth  (moderator)

_________________
http://WilsonMinesCo.com/ lots of 6502 resources
The "second front page" is http://wilsonminesco.com/links.html .
What's an additional VIA among friends, anyhow?
Top
 Profile  
Reply with quote  
BigDumbDinosaur
 Post subject: Re: A new toy memory map
PostPosted: Thu Nov 21, 2024 12:08 am 
Offline
User avatar

Joined: Thu May 28, 2009 9:46 pm
Posts: 8514
Location: Midwestern USA
GARTHWILSON wrote:
agsb wrote:
PS. I repost this at SBC topics

Please don't, as it adds needless clutter to the forum...

Also, please don’t post schematics in color.  :D

As for your circuit, what is the purpose of the ENABLE input to the read/write logic?  If it is low during a write cycle, /WR will stay high, producing write-protection for something.  However, I don’t see anything that would need write-protection.

The memory map you are planning is not possible with your current design.  You are indicating that “devices” will be mapped into the range $E000-E0FF in 16-byte segments. You will need a lot more address bus decoding to achieve that than you have now.  I suggest you rethink your memory map and look at using a 74xx138 3-8 decoder to select your I/O devices.

_________________
x86?  We ain't got no x86.  We don't NEED no stinking x86!
Top
 Profile  
Reply with quote  
agsb
 Post subject: Re: A new toy memory map
PostPosted: Thu Nov 21, 2024 5:43 am 
Offline

Joined: Mon Jan 09, 2023 9:33 pm
Posts: 29
Thanks. Garth  (moderator)[/color][/quote]

I know, I had already posted here when I noticed that there was a topic about SBC, I tried to delete it here and just leave it there, but I couldn't.
Which of the two should I delete (how)?
Sorry, I had already posted it when I remembered the colors, I'll put it back in black and white.
Thank you for your attention and patience.
Top
 Profile  
Reply with quote  
agsb
 Post subject: Re: A new toy memory map
PostPosted: Thu Nov 21, 2024 5:48 am 
Offline

Joined: Mon Jan 09, 2023 9:33 pm
Posts: 29
The ENABLE signal is for suspend both RD and WR, if need, or just tied to VDD 5V.

Quote:
[color] I suggest you rethink your memory map and look at using a 74xx138 3-8 decoder to select your I/O devices. [/color]


Yes, exact what I plan to do.
Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 

Board index » 6502.org Users Forum » Hardware

All times are UTC


Who is online

Users browsing this forum: No registered users and 29 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
6502.org is an ongoing project by Mike Naberezny and contributors.