6502.org Forum Projects Code Documents Tools Forum
It is currently Fri Nov 22, 2024 5:22 pm

View unanswered posts | View active topics


Board index » 6502.org Users Forum » Newbies

All times are UTC




Post new topic Reply to topic  Page 1 of 2
  [ 22 posts ]  Go to page 1, 2  Next
  Previous topic | Next topic 
Author Message
nimbus396
 Post subject: Generic for loop
PostPosted: Wed Feb 12, 2020 4:13 pm 
Offline

Joined: Wed Feb 12, 2020 4:05 pm
Posts: 5
I see in these forums, there are a lot about loops but, is there a better way than the following to have a 16 bit for loop where the loop count can change and it is just a call. I have the following piece of code I developed using Skrilldricks page to loop for a specific count. I am developing for the Atari 2600 and I would really just like to have one loop that I can set the loop counter

Code:

define scrLow $00
define scrHigh $01
define color #1

lda #0
sta scrLow
lda #$02
sta scrHigh
ldx #0
ldy #1

fill:      lda scrColor       ; set the color
           sta (scrLow,x)     ; put it on the screen
           lda scrLow         ; load the low byte
           clc                ; clear the carry
           adc #1             ; add one to low byte
           sta scrLow         ; store low byte
           lda scrHigh        ; load the high byte
           adc #0             ; add carry to high byte
           sta scrHigh        ; store it
           cmp #$06           ; compare high byte
           bne fill           ; != so increment low byte
           lda scrLow         ; load low byte
           cmp #$00           ; compare low byte
           bne fill           ; != so increment low byte
     
end:       brk
Top
 Profile  
Reply with quote  
floobydust
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 4:44 pm 
Offline
User avatar

Joined: Tue Mar 05, 2013 4:31 am
Posts: 1385
Incrementing a 16-bit pointer is easy, no need for CLC, ADC #$01, STA xxxx, etc. You can just use INC xxxx and BNE as:

Code:
;INCINDEX subroutine: increment 16 bit variable INDEXL/INDEXH
INCINDEX        INC     INDEXL          ;Increment index low byte
                BNE     SKP_IDX         ;If not zero, skip high byte
                INC     INDEXH          ;Increment index high byte
SKP_IDX
; more code goes here, like LDA INDEXH, followed by CMP #$06


Also, you don't need to do a CMP #0 after a LDA, as the zero flag is set upon loading the A reg if the value is zero.

Code:
LDA     LENL            ;Get length low byte
BEQ     SKP_LENH        ;Test for LENL = zero, branch is zero


Using the above code examples will shorten both your code and execution time.

_________________
Regards, KM
https://github.com/floobydust
Top
 Profile  
Reply with quote  
drogon
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 4:49 pm 
Offline
User avatar

Joined: Wed Feb 14, 2018 2:33 pm
Posts: 1488
Location: Scotland
The bit where you add 1 to the 16-bit value can be improved to:

Code:
    inc    scrLow
    bne    :+
    inc    scrHigh
:


rather than the lda, clc, add, sta sequence.

This also preserves the value in A, although the compare will corrupt it.

also the LDA.. CMP #$00 - the CMP isn't needed as the flags are explicitly set on the LDA, so simply

Code:
    lda    scrLow
    bne    fill


will work.

Cheers,

-Gordon

_________________
--
Gordon Henderson.
See my Ruby 6502 and 65816 SBC projects here: https://projects.drogon.net/ruby/
Top
 Profile  
Reply with quote  
nimbus396
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 4:57 pm 
Offline

Joined: Wed Feb 12, 2020 4:05 pm
Posts: 5
Thank you, I will give that a try
Top
 Profile  
Reply with quote  
nimbus396
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 5:14 pm 
Offline

Joined: Wed Feb 12, 2020 4:05 pm
Posts: 5
Save 5 bytes :). While I agree, comparing zero doesn't need to be there, if the low byte is non-zero, the compare does?

I see I have a lot more studying to do on Flag usage. Flag states seem to be able to remove cycles if used correctly.

Code:
;************** Old Code using ADC
define scrLow $00
define scrHigh $01
define scrColor #1

lda #0
sta scrLow
lda #$02
sta scrHigh
ldx #0

fill:      lda scrColor       ; set the color
           sta (scrLow,x)     ; put it on the screen
           lda scrLow         ; load the low byte
           clc                ; clear the carry
           adc #1             ; add one to low byte
           sta scrLow         ; store low byte
           lda scrHigh        ; load the high byte
           adc #0             ; add carry to high byte
           sta scrHigh        ; store it
           cmp #$05           ; compare high byte
           bne fill           ; != so increment low byte
           lda scrLow         ; load low byte
           cmp #$24           ; compare low byte
           bne fill           ; != so increment low byte
     
end:       brk


Code:
; ************** New code using INC

define scrLow $00
define scrHigh $01
define scrColor #3

lda #0
sta scrLow
lda #$02
sta scrHigh
ldx #0

fill:      lda scrColor       ; set the color
           sta (scrLow,x)     ; put it on the screen
           inc scrLow
           bne skipIdx
           inc scrHigh
skipIdx:   lda scrHigh
           cmp #$05           ; compare high byte
           bne fill           ; != so increment low byte
           lda scrLow         ; load low byte
           cmp #$24           ; compare low byte
           bne fill           ; != so increment low byte
     
end:       brk
Top
 Profile  
Reply with quote  
cjs
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 5:30 pm 
Offline
User avatar

Joined: Sat Dec 01, 2018 1:53 pm
Posts: 730
Location: Tokyo, Japan
nimbus396 wrote:
I see I have a lot more studying to do on Flag usage. Flag states seem to be able to remove cycles if used correctly.

Right. Specific opcodes set specific flags for a reason, and to write efficient assembly code you must know which opcodes set which flags. Once you get good you'll find yourself freqently using flags set not in the previous instruction but several instructions back. You'll also find that, when you return status via flags in your own routines, careful selection of the flags and their values for certain cases will make things more efficient. (E.g., you might choose to use the carry over other flags, and particular meanings for set or clear on routine from a subroutine, because those flag values just "fall out" of the code you wrote without any flag tests or sets/clears.)

_________________
Curt J. Sampson - github.com/0cjs
Top
 Profile  
Reply with quote  
drogon
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 5:33 pm 
Offline
User avatar

Joined: Wed Feb 14, 2018 2:33 pm
Posts: 1488
Location: Scotland
nimbus396 wrote:
Save 5 bytes :). While I agree, comparing zero doesn't need to be there, if the low byte is non-zero, the compare does?

I see I have a lot more studying to do on Flag usage. Flag states seem to be able to remove cycles if used correctly.


Code:
; ************** New code using INC

define scrLow $00
define scrHigh $01
define scrColor #3

lda #0
sta scrLow
lda #$02
sta scrHigh
ldx #0

fill:      lda scrColor       ; set the color
           sta (scrLow,x)     ; put it on the screen
           inc scrLow
           bne skipIdx
           inc scrHigh
skipIdx:   lda scrHigh
           cmp #$05           ; compare high byte
           bne fill           ; != so increment low byte
           lda scrLow         ; load low byte
           cmp #$24           ; compare low byte
           bne fill           ; != so increment low byte
     
end:       brk


One thing to note here... The lda scrColor. I don't know what assembler you're using, but this may load from location 3 rather than the immediate value 3.

Also, if you use Y for the scrHigh/Low cmp, you don't alter A, so can save the lda scrColor every time through the loop. (Do it once then the fill label goes on the sta line. You also mention the Atari 2600 (which I know little about other than using them back in the day), if this has a 6502 then "as you were", but if it's something else with a 65C02, then the sta (scrLow,x) can simply be sta (scrLow) which leaves X free for something else, if needed.

Anothe thing to think about (in the '2600 where I understand every cycle is preciously counted!) is having essentially 2 copies of this code too - if you have the ROM space for it... The first version just compares scrHigh and when this matches then you drop into the 2nd copy which just compares scrLow - because we know that scrHigh is already matching at that point, so no need to keep checking. This is a speed optimisation for the value of scrLow - in this case you'll save $24 compares of scrHigh which will always match - so the trade-off is speed for extra ROM space.

-Gordon

_________________
--
Gordon Henderson.
See my Ruby 6502 and 65816 SBC projects here: https://projects.drogon.net/ruby/
Top
 Profile  
Reply with quote  
nimbus396
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 5:54 pm 
Offline

Joined: Wed Feb 12, 2020 4:05 pm
Posts: 5
Not really an assembler. I play around with ideas using https://skilldrick.github.io/easy6502/#intro. It is an online emulator written in JS with a step debugger and monitor. However, I can see now, doing the coding on the hardware would probably be better; the indirect addressing mode (<address>) is only available for JMPs in the emulator. but, (<address>,x) and (<address>),y are available. So, coding on the hardware will allow for optimizations. The finished skrilldrick code is below. Any suggestions on good books for optimizing algorithms with the 6502?

Code:
define scrLow $00       ; Screen memory
define scrHigh $01

define lpLow $02        ; Loop Counter
define lpHigh $03

; Setup the screen start

lda #0                   ; Store 0 to screen low
sta scrLow              ; byte
lda #$02                ; Store $02 to screen high
sta scrHigh             ; byte : screen start (512)

; Set the loop counter max value

lda #$24                ; Store $24 to loop counter low
sta lpLow               ; byte
lda #$05                ; Store $05 to loop counter high
sta lpHigh              ; byte : loop counter (1316)
ldx #0

fill:      lda #3             ; set the color
           sta (scrLow,x)     ; put it on the screen
           inc scrLow         ; increment low byte
           bne skipIdx        ; skip if not zero
           inc scrHigh        ; increment high byte
skipIdx:   lda scrHigh        ; load high byte
           cmp $03            ; compare high byte
           bne fill           ; != so increment low byte
           lda scrLow         ; load low byte
           cmp $02            ; compare low byte
           bne fill           ; != so increment low byte
     
end:       brk
Top
 Profile  
Reply with quote  
leepivonka
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 6:13 pm 
Offline

Joined: Fri Apr 15, 2016 1:03 am
Posts: 140
Here is a version (untested) that is callable & takes advantage of the quirks of the 6502's registers & addressing modes.
Code:
define Ptr $00  ; 2 bytes
define Temp1 $02  ; 2 bytes

;---------------------------------------------
; Main

        ; fill a section of screen memory
        lda #$40    ; Ptr=$240
        sta Ptr+0
        ldy #$2
        sty Ptr+1
        ldx #3      ; Len=$380
        ldy #$80
        lda #3      ; color value
        jsr Fill

        ; fill another section of screen memory
        lda #0      ; Ptr=$200
        sta Ptr+0
        ldy #2
        sty Ptr+1
        ldx #4      ; Len=$400
        ldy #0
        lda #1      ; color value
        jsr Fill

        brk

; -------------------------------------
Fill: ; Fill memory starting at Ptr for XY bytes with A.
    ; Values in Ptr & Temp1 & X & Y are destroyed.

        sty Temp1+0 ; save length lo byte
        ldy #0      ; init block index

        ; fill full 256byte blocks
        cpx #0      ; if no full blocks
        beq @22     ;    skip to the partial block code
@12:    sta (Ptr),y ; store
        iny         ; step to next block index
        bne @12     ; loop until block is done
        inc Ptr+1   ; step to next block
        dex
        bne @12     ; loop until all full blocks are done
        beq @22     ; branch always

        ; fill last partial 256byte block
@21:    sta (Ptr),y ; store
        iny         ; step to next block index
@22:    cpy Temp1+0 ; loop until block is done
        bne @21

        rts
Top
 Profile  
Reply with quote  
GARTHWILSON
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 6:25 pm 
Offline
User avatar

Joined: Fri Aug 30, 2002 1:09 am
Posts: 8543
Location: Southern California
nimbus396, welcome.

Although the example you give is to fill a screen, what you wrote at the top of your head post seems to indicate you would like a general-purpose 16-bit FOR...NEXT loop. There's one in the set of my pages about program structures in assembly language with macros, at http://wilsonminesco.com/StructureMacros/#for16 which is about 80% of the way down the page. It allows you to do for example,

Code:
        FOR  var1, 1, TO, 5000     ; Loop 5,000 times.
           <actions>
           <actions>
           <actions>
        NEXT  var1

(In the macro invocation line, the C32 assembler I use requires the commas between the input parameters, as I'm sure most assemblers do.) The macro source code is about 70% of the way down the page at http://wilsonminesco.com/StructureMacros/STRUCMAC.ASM . The code it will lay down is:

Code:
          LDA   #<starting counter value low byte>
          STA   <variable name>
          LDA   #<starting counter value high byte>
          STA   <variable name> + 1

              <do your stuff here>

          INC   <variable name>
          BNE   nx1
          INC   <variable name> + 1

 nx1:     LDA  <variable name>
          CMP  #<FOR limit + 1, low byte>
          BNE  <top of loop>

          LDA  <variable name> + 1
          CMP  #<FOR limit + 1, high byte>
          BNE  <top of loop>
                                     ; If, after being incremented, the specified variable
                                     ; matches the limit + 1 (checking both bytes), drop through.

Note that X and Y are not used at all. A is used once at the beginning for the FOR setup and then used each time NEXT runs; but you can use it for whatever you want inside the loop as long as it's ok for it to get modified by NEXT.

Where it says BNE <top of loop>, the target address is of the first instruction after the setup's STA <variable name> + 1. Where it says "<variable name> + 1," that's the high byte of the variable you're using as a counter, whereas where it says "FOR limit + 1," that's a constant (as you might have guessed from the "#" immediate indicator in front of it). So the variable is loaded with LDA (could be ZP or absolute, your preference) and compared with CMP#. NEXT uses two pieces of information left by the FOR macro: the desired limit, and the address of the top of the loop to branch up to when the limit has not been reached yet.

All of the program flow-control structure macros I give in that section of the website are nestable except this 16-bit FOR...NEXT and the CASE structure. (They can be inside other program structures, and you can have other program structures inside them; but you cannot have one 16-bit FOR...NEXT loop inside another 16-bit FOR...NEXT loop or one CASE structure inside another CASE structure.)

If you ever decide to move up to the 65816, since it has 16-bit index registers, doing something 5,000 times as shown above becomes as efficient as the 6502 handles numbers under 256.

_________________
http://WilsonMinesCo.com/ lots of 6502 resources
The "second front page" is http://wilsonminesco.com/links.html .
What's an additional VIA among friends, anyhow?
Top
 Profile  
Reply with quote  
BigEd
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 6:33 pm 
Offline
User avatar

Joined: Thu Dec 11, 2008 1:28 pm
Posts: 10985
Location: England
Indeed, welcome! For Atari 2600 development you might like Steven Hugg's in-browser IDE which includes an emulator:
https://8bitworkshop.com/v3.5.0/?platfo ... %2Fhello.a
Top
 Profile  
Reply with quote  
commodorejohn
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 7:05 pm 
Offline

Joined: Thu Jan 21, 2016 7:33 pm
Posts: 282
Location: Placerville, CA
nimbus396 wrote:
I see I have a lot more studying to do on Flag usage. Flag states seem to be able to remove cycles if used correctly.

Absolutely. A lot of tweaking/optimizing in assembler is in finding ways to avoid doing anything you don't have to; since the 6502 already does some basic comparisons and sets flags accordingly on the results of most instructions, it's often possible to know a variety of things without ever having to use a CMP: was the result zero? Negative? If the last instruction was an INC/INX/INY and the Z flag is set, it means the value rolled over, so if it's part of a larger variable you know to carry over the increment to the next most significant byte...things like that. Furthermore, if you can arrange circumstances correctly (without making the rest of your code too obscure,) you can get this to be the case more often.
Top
 Profile  
Reply with quote  
nimbus396
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 7:12 pm 
Offline

Joined: Wed Feb 12, 2020 4:05 pm
Posts: 5
I appreciate all the support :)
Top
 Profile  
Reply with quote  
BillO
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 9:30 pm 
Offline
User avatar

Joined: Fri Dec 12, 2008 10:40 pm
Posts: 1007
Location: Canada
Maybe there is something I don't get here, but at the risk of sounding dumb (when has that ever stopped me?)


Looking at this:
Code:
fill:      lda #3             ; set the color
           sta (scrLow,x)     ; put it on the screen
           inc scrLow         ; increment low byte
           bne skipIdx        ; skip if not zero
           inc scrHigh        ; increment high byte
skipIdx:   lda scrHigh        ; load high byte
           cmp $03            ; compare high byte
           bne fill           ; != so increment low byte
           lda scrLow         ; load low byte
           cmp $02            ; compare low byte
           bne fill           ; != so increment low byte
     
end:       brk


x is never changed so why are you doing sta(scrLow,x)?

Also, is scrHigh is not incremented then why do the load and compare on it every time?

Would this not work more efficiently?
Code:
fill:      lda #3             ; set the color
           sta (scrLow)       ; put it on the screen
           inc scrLow         ; increment low byte
           bne fill           ; loop if not zero
           inc scrHigh        ; increment high byte
           lda scrHigh        ; load high byte
           cmp $03            ; compare high byte
           bne fill           ; != so increment low byte
           lda scrLow         ; load low byte
           cmp $02            ; compare low byte
           bne fill           ; != so increment low byte
     
end:       brk

_________________
Bill


Last edited by BillO on Wed Feb 12, 2020 11:06 pm, edited 1 time in total.

Top
 Profile  
Reply with quote  
sark02
 Post subject: Re: Generic for loop
PostPosted: Wed Feb 12, 2020 9:32 pm 
Offline

Joined: Tue Nov 10, 2015 5:46 am
Posts: 230
Location: Kent, UK
I thought I'd jump in with an attempt. I tested this on the easy6502 you mentioned, and it appears to work.

The main feature of the code below is that the fill loop is:

Code:
l1:   
    sta ($20),y
    iny
    bne l1
    inc $21
    dex
    bpl l1


XY bytes are written, even if Y != 0. In this case, the function adjusts the ($21,$20) start location backwards (256-Y) bytes, and advances Y that same amount so as to enter the loop with everything setup. The goal is to keep the performance critical loop minimal.

The adjustment code looks long and awkward; there must be a more elegant way to do it, but my priority was getting to the loop.

Code:
; Fill XY bytes of memory with A, starting
; at ($21,$20)
; clobbers $22
fill:
   cpy #0
   beq l2
   pha
   tya
   eor #$ff
   sta $22
   inc $22
   lda $22
   tay
   sec
   lda $20
   sbc $22
   sta $20
   lda $21
   sbc #0
   sta $21
   pla
l1:
   sta ($20),y
   iny
   bne l1
   inc $21
l2:
   dex
   bpl l1
   rts


It's not a generic loop by any means.
Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 22 posts ]  Go to page 1, 2  Next

Board index » 6502.org Users Forum » Newbies

All times are UTC


Who is online

Users browsing this forum: No registered users and 5 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
6502.org is an ongoing project by Mike Naberezny and contributors.