6502.org
http://forum.6502.org/

ATF1508 Development Board?
http://forum.6502.org/viewtopic.php?f=10&t=6373		 Page 1 of 1
Author:  cbmeeks [ Tue Nov 17, 2020 4:04 pm ]
Post subject:  ATF1508 Development Board?
I was wondering if anyone knows of a development board for working with the ATF1508? Just something that had the pins out on headers and easy programming with the JTAG cable?

Something breadboard friendly would be nice.

Thanks!


BTW, I found this but it's way too expensive for what I want.

https://www.digikey.com/en/products/det ... AZhgBVajSA
Author:  cbscpe [ Tue Nov 17, 2020 4:48 pm ]
Post subject:  Re: ATF1508 Development Board?
I have built a break-out board for the ATF1504

Attachment:
File comment: ATF1504 Breakoutboard
IMG_4156.jpeg
IMG_4156.jpeg [ 1.71 MiB | Viewed 1552 times ]


And use a ATDH1150USB-K ISP Cable to program it in circuit.

I have also one of these

Attachment:
File comment: PLCC-84 Breadboard Adapter
PLCC_Adapter__84_4a0067d10344b.jpg
PLCC_Adapter__84_4a0067d10344b.jpg [ 35.87 KiB | Viewed 1552 times ]


But it is very time-consuming to connect all 84-pins.

In most cases a ATF1504 is enough to test new things and then I just copy the code over the ATF1508 in the final design

Peter
Author:  BigDumbDinosaur [ Tue Nov 17, 2020 5:07 pm ]
Post subject:  Re: ATF1508 Development Board?
cbmeeks wrote:
BTW, I found this but it's way too expensive for what I want.

https://www.digikey.com/en/products/det ... AZhgBVajSA

I happen to have one of those, along with several adapters. I haven't used it nearly as much as I thought I would.
Author:  BitWise [ Tue Nov 17, 2020 6:21 pm ]
Post subject:  Re: ATF1508 Development Board?
BigDumbDinosaur wrote:
cbmeeks wrote:
BTW, I found this but it's way too expensive for what I want.

https://www.digikey.com/en/products/det ... AZhgBVajSA

I happen to have one of those, along with several adapters. I haven't used it nearly as much as I thought I would.

Ditto
Author:  cbmeeks [ Tue Nov 17, 2020 6:51 pm ]
Post subject:  Re: ATF1508 Development Board?
Thanks guys. Yeah, my parts bin is full of kits and boards I thought I would use more. lol

Which is why I'd like to go a cheaper route. Now, I do have a PLCC-84 to DIP board but it's not vertical. Which means it takes about 20 square feet of breadboard. lol

Ugh. I may just layout a small board myself and just have it made. Shouldn't cost too much.


@cbscpe
Do you have any of those to sell?
Author:  cbscpe [ Fri Nov 20, 2020 11:13 am ]
Post subject:  Re: ATF1508 Development Board?
I have spare ones. Just drop me PM with your postal address so I can send two of them to you (it's a give away)

Peter
Author:  cbmeeks [ Fri Nov 20, 2020 2:03 pm ]
Post subject:  Re: ATF1508 Development Board?
Thank you! I certainly don't mind paying.

PM on the way.
Page 1 of 1 All times are UTC
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/